HOME CONTACT NEWS EVENTS
Products > Residential Products > Series 8HE
Series 8HE Oil-Fired Hot Water or Steam Boiler

Series 8 Hot Water/Steam oil fired boiler
The 8HE Series, with its rugged cast iron construction, offers commercial quality in a residential boiler. With cast iron sections, the Series 8HE offers a multitude of performance advantages including higher heat retention, better combustion, quiet operation and superior steam performance. The cast iron sections on the Series 8HE are factory tested and assembled with steel push nipples. These sections offer larger water content and increased water surface area in the boiler. Corrosion and mineral build-up is minimized and maximum heat transfer is maintained. This larger water content also reduces unnecessary make-up water in steam applications and quicker start-up is facilitated by better steam generation.

Thicker Walls and Higher Mass

The thicker walls and higher mass of the Series 8HE boiler maintains a high water temperature for a greater length of time after the burner has stopped firing. This higher heat retention reduces short cycling for maximum efficiency.

Advanced Control Platform

The Hydrostat® Temperature Limit Control uses Thermal Targeting technology to analyze thermostat activity and continually evaluates how much heat the building requires. To further enhance fuel efficiency, on a call for heat, the unit will energize the circulator pump to drive the residual latent heat from the boiler to the heating zone in an attempt to satisfy the heat demand without firing up the burner.


Hydrostat® Enhanced Digital Display with:

  • Dial-Type Settings, allow for quick and easy set-up.
  • Diagnostic Lights, continually indicates which features are active and if the control is holding the burner off for any reason. No complicated menus to scroll through.


Service Made Simple

The cast iron burner mounting plate is hinged to the boiler for a full swingout access to the combustion chamber while the burner is still attached allowing for quick and easy cleaning and servicing. From top of boiler, use a standard flue brush to clean between the tapered section pins.

Convertible Flue

The Series 8HE (3 & 4 section) boilers are assembled and packaged with flue exiting the rear of the boiler. For installations requiring a top flue, simply remove jacket top and reverse flue director to top.

Built and Backed for a Lifetime

Without question, cast iron construction offers superior durability and longer life. Each Series 8HE section is pressure tested and retested upon assembly. Your complete satisfaction on all Series 8HE boilers is backed by a lifetime warranty* and our commitment to excellence.(see warranty statement for complete details).
PRODUCT LITERATURE

STANDARD FEATURES
All Boilers
  • Cast Iron Sections - Factory Tested and Assembled with Steel Push Nipples
  • Deluxe Powder Coated Steel Insulated Jacket
  • Preformed Target Wall
  • Full Swing-out Service Door
  • Easy Top Cleanout Access
  • Rear or Top Flue Convertibility (3 & 4 Sections)
  • Built-In Air Elimination Port
  • Molex quick electrical connection to burner

Water Boilers
  • Hydrostat Combination Low Water Cut-off and Universal Temperature Limit Control
  • DHW Priority with Overide Protection
  • Hydrostat Provides Cold-Start and Tankless Coil Operation
  • ASME Safety Relief Valve (30 psi)
  • Temperature-Pressure Gauge
  • Taco Circulator
  • Drain Valve

Steam Boilers
  • Hi-Limit Pressure Control
  • A.S.M.E. Safety Relief Valve (15 psi)
  • Steam Pressure Gauge
  • Gauge Glass and Fittings
  • Low Water Cutoff HydroLevel Cycle Guard
  • 1 1/4" Skim Tapping

OPTIONAL EQUIPMENT
Steam and Water
  • Beckett AFG w/GeniSys Advanced Burner Control, Carlin EZ-Pro or Riello Flame Retention Burners w/ Nozzle
  • Tankless Coil Heater
This product is ENERGY STAR® certified. Click to learn about federal tax credits

*Energy Star applies only to water boilers

Bookmark and Share